Vistaquest N7227V5 Manuel d'utilisateur télécharger pdf (Page 35)

– 35 –

ZN ZT – RC In: L

10 00 – 00 RF: 1

5. A display will appear, showing a summary of that zone's programming.

If the zone is not programmed, the display will appear as shown here. If

checking a zone's programming, and it is programmed satisfactorily,

press [#] to back up one step and enter another zone number, if

desired. Otherwise, press [

✱

] to continue.

↓ Zone Number

10 Zone Type

Perimeter 03

Entry for Zone Type 03

shown

6. Each zone must be assigned a zone type, which defines the way in

which the system responds to faults in that zone. Enter the zone type

desired (or change it, if necessary). Available zone types are:

00 = Zone Not Used 08 = 24 Hr Aux

01 = Entry/Exit #1, Burglary 09 = Fire

02 = Not used 10 = Interior w/Delay

03 = Perimeter 20 = Arm–Stay*

04 = Interior Follower 21 = Arm–Away*

05 = Trouble Day/Alarm Night 22 = Disarm*

06 = 24 Hr Silent 23 = No Alarm Response

07 = 24 Hr Audible

(EX: Relay activation)

* These are special zone types used with 5800 series wireless pushbutton

units which will result in arming the system in the STAY or AWAY mode, or

disarming of the system, depending on the selection made. A button

programmed for these functions will report the zone number of the button as

the user number that armed/disarmed to the central station.

Press [

✱

] to continue.

10 Report Code

1st 03 2nd 12 3C

7. Enter the report code. The report code consists of 2 hexadecimal digits,

each in turn consisting of 2 numerical digits. For example, for a report

code of "3C", enter [0][3] for "3" and [1][2] for "C."

(Refer to the

SYSTEM COMMUNICATION

section for more information

about report codes and report code formats.)

Press [

✱

] to continue.

10 Input Dev: LP #

Rf Trans. RF: 1

8. Enter the transmitter input device type as follows:

3 = RF (supervised RF transmitter)

4 = UR (unsupervised RF transmitter)

5 = BR (button type RF transmitter - unsupervised)

(Refer to the separate Programming Guide for input types.)

Press [

✱

] to continue.

10 Input Dev: LP#

RF Trans. RF: 1

9. The cursor should now be flashing above the loop number. The default

is "1." To accept this, press [

✱

]. If a different loop number is being used

on this transmitter, enter the loop number (1–4) and press [

✱

] to

continue (see the loop designations for various transmitters in the

separate Programming Guide). The loop number must be entered

here, whether using Zone Programming or Sequential Mode to

"enroll" transmitters.

10 Learn S/N?

0 = No, 1 = Yes 0

10. If the transmitter’s serial number has not been previously “enrolled,” you

may enter the enroll mode now by either entering "1" (Yes)

pressing the upper left-hand button of the “program tool”. If using the

program tool, move to the physical location of the transmitter to be

enrolled before pressing the button. A single short beep will verify that

the button has been pressed. The system will respond to the first serial

number transmitted after the [

✱

] key on the keypad or the button of the

program tool is pressed.

Enter "0" (No) if you wish to enroll the transmitter later, using the

“sequential” mode in

Section 13. SEQUENTIAL MODE

If "0" (No) is entered, go to step 13 (skip steps 11 and 12).

10 Input S/N: L

A X X X–X X X X

11. This prompt is displayed if "1" (Yes) is entered in response to the "Learn

S/N?" prompt. The serial number may be enrolled by one of two methods:

a) Enter the 7-digit serial number printed on the transmitter using a

Alpha keypad, or

b) Activate the transmitter by faulting

restoring the input you wish to

use for that zone (e.g., press a button, open or close a door, etc.).

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Vistaquest N7227V5 Manuel d'utilisateur Page 35

Commentaires sur ces manuels