Vistaquest N7227V5 Manuel d'utilisateur Page 42
- Page / 88
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
– 42 –
Output Relay Displays
Enter Relay No.
(00 = Quit) 01
Upon pressing
✱
80, this screen will appear. Enter the Relay Number 01, 02,
03, or 04 for a 4204 (or 00 to end these entries). Press the [
✱
] key to
continue.
The [
✱
] key is used to accept an entry and advance to the next prompt. The
[#] key is used to revert back to the last question to check or change an
entry. Press [
✱
] to go forward again.
02 A EV ZL ZT
STT 0 0 0 00
This screen displays a summary of the current Relay START programming
(for this example, relay 02 has been selected).
Press the [
✱
] key to continue.
02 A EV ZL ZT
STP – – 0 00
This screen displays a summary of the current Relay STOP programming.
Press the [
✱
] key to continue.
02 Relay Action
No Response 0
Enter the desired relay action as listed below. Press the [
✱
] key to continue.
0 = No response 2 = Close and Stay Closed
1 = Close for 2 seconds 3 = Continuous Pulse on & off (1 sec ON, 1 sec OFF)
02 Start Event
Not Used 0
Enter the event to START the relay:
0 = Not used; 2 = Fault; 1 = Alarm; 3 = Trouble
A zone list must be used in conjunction with an event. If a zone type/system
operation is to be used instead of an event, enter 0.
Press the [
✱
] key to continue.
02 Start: Zn List
No List 0
If a zone list will be used to START the relay action, enter the zone list number
(to be programmed in field
✱
81): 1, 2, or 3. If not used, enter 0. Press the [
✱
]
key to continue.
02 Start: Zn Typ
Not Used 00
If a zone type or system operation will be used to START the relay action,
enter the appropriate two-digit code (see table that follows). If not, enter 00.
Press the [
✱
] key to continue.
CHOICES FOR ZONE TYPES
00 = Not Used 05 = Trouble Day/Alarm Night 08 = 24 Hr Aux
01 = Entry/Exit 06 = 24 Hr Silent 09 = Fire
03 = Perimeter 07 = 24 Hr Audible 10 = Interior w/Delay
04 = Interior Follower
CHOICES FOR SYSTEM OPERATION
20 = Arming–Stay 33 = Any Burglary Alarm 39 = Any Fire Alarm
21 = Arming–Away 34 = Code + # + 7 Key Entry 40 = Bypassing
22 = Disarming (Code + OFF) 35 = Code + # + 8 Key Entry 41 = AC Power Failure
31 = End of Exit Time 36 = At Bell Timeout** 42 = System Batt. Low
32 = Start of Entry Time 38 = Chime 58 = Duress
**Or at Disarming, whichever occurs earlier.
02 Stop: Zn List
No List 0
If a zone list will be used to STOP, or restore, the relay action, enter the zone list
(ZL) number 1, 2, or 3 (to be programmed in
✱
81 mode). If not used, enter 0.
Press the [
✱
] key to continue.
02 Stop: Zn Typ
Not Used 00
If a zone type or system operation will be used to STOP the relay action, enter
the appropriate two digit code (see the "ZT" choices listed above). If not, enter
00. Press the [
✱
] key to continue.
02 A EV ZL ZT
STT 0 0 0 00
This screen again displays a summary of the current relay START
programming.
Press the [
✱
] key to continue.
02 A EV ZL ZT
STP – – 0 00
This screen again displays a summary of the current relay STOP programming.
Press the [
✱
] key to continue.
- VISTA-10 1
- Heat-Activated Detectors 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- HOW TO USE THIS MANUAL 7
- Wireless Expansion: 9
- Mounting the Cabinet 11
- Installing the Lock (if used) 11
- DETAIL B 12
- SIDE VIEW OF 12
- LONG MOUNTING CLIPS 12
- 17 18 19 20 21 13
- Wiring The AC Transformer 14
- Keypads That May Be Used 15
- Mounting the Keypads 16
- SUPPLEMENTARY 17
- POWER SUPPLY 17
- 4-WIRE SMOKE 18
- DETECTORS 18
- Programming Hard-Wired Zones 19
- SYSTEM COMMUNICATION 20
- DESCRIPTOR PROGRAMMING 20
- Programming Panic Keys 20
- (5700 or 5800 series) 22
- ZONE RESPONSE TYPE 25
- DEFINITIONS 25
- IMPORTANT 26
- SET SWITCHES WITH 26
- BATTERY REMOVED 26
- ✱24, and the wireless key 27
- Example: 29
- SYSTEM COMMUNICATIONS 29
- ALPHA DESCRIPTOR PROGRAMMING 30
- 5800 Series Transmitter Setup 31
- responses (e.g. 32
- Data field 33
- SEQUENTIAL MODE 34
- – RC In: L 35
- Section 13. SEQUENTIAL MODE 36
- (Continued) 37
- restores 40
- Zone List Displays 43
- Section 7. 4285 PHONE MODULE 44
- Not Used 45
- VOICE MODULE 46
- Section 8. EXTERNAL SOUNDERS 49
- Section 9. LONG RANGE RADIO 51
- General Information 52
- TERMINALS 53
- ON CONTROL 53
- Section 11. FINAL POWER UP 54
- Section 12 56
- ✱ ZN 01 ZONE 01 57
- ✱ ZN 01 A 57
- ✱ ZN 01 B ACK 57
- ✱ ZN 01 BACK 57
- ZN 01 BACK 58
- = Yes 00 58
- ALPHA VOCABULARY LIST 60
- Section 13. SEQUENTIAL MODE 61
- Serial # 62
- TESTING THE SYSTEM 63
- Communication Programming 66
- (continued) 67
- 11 2 68
- TESTING THE SYSTEM 70
- Test Procedure 71
- TO THE INSTALLER 72
- Section 16. SYSTEM OPERATION 73
- Assigning the Master Code 74
- Panic Keys 74
- SYSTEM (including Wireless) 77
- SMOKE DETECTOR 78
- CONTACTING TECHNICAL SUPPORT 79
- Specifications 80
- Ademco VISTA–10SE 81
- 4285 PHONE MODULE 81
- REGULATORY AGENCY STATEMENTS 83
- UL NOTICES 84
- (DOC) STATEMENT 85
- WARNING! 86
- WARNING: 87
- ADEMCO LIMITED WARRANTY 88
© 2020, manymanuals.fr. Tous droits réservés | 0.800 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels