Vistaquest N7227V5 Manuel d'utilisateur télécharger pdf (Page 78)

– 78 –

TROUBLESHOOTING GUIDE (continued)

SYMPTOM POSSIBLE CAUSE REMEDY

7. Intrusion alarm for no ap-

parent reason. (continued)

7d. Magnetic contacts improperly connected or

wire broken.

7e. Entry door programmed as “Instant”

7f. Loose fitting door or window being rattled

by wind or vibrations.

7d. Check wiring connections. Be sure wires

are properly stripped and are tightly

fastened to screw terminals.

7e. Check and revise programming. Re-

program transmitter number.

7f Mount magnet closer to magnet.

8. Repeated low battery signal. 8a. Transmitter located where temperature

drops below 32°F.

8b. Poor quality or unspecified battery in

transmitter.

8c. Transmitter malfunctioning.

8a. Change location. Use magnetic contacts to

protect opening.

8b. Check battery. Use only batteries specified

in the instructions (does not apply to

transmitters with non-replaceable

batteries).

8c. Replace faulty transmitter.

9. Local bell and keypad sound

continuously after arming.

9. Exit or interior zone contained a fault at end

of Exit Delay (e.g., Exit door left open).

The "Exit Alarm" display, etc. will also

result if an alarm from an exit or interior

zone occurs within two minutes after the

end of an exit delay

→

9a. If system disarmed

before

ensuing entry

time runs out, "CA" or "Canceled Alarm"

will be displayed. Sounding will stop.

9b. If system

not

disarmed before entry time

ends, "EA" or "Exit Alarm" will be displayed

and Exit Alarm message will be sent to

central station. Sounding will continue until

system is disarmed or timeout occurs.

Clear display by entering code + OFF a second

time. Avoid fault when re-arming.

CONTROL

SYMPTOM POSSIBLE CAUSE REMEDY

1. "POWER" light off or

“NO AC” displayed

1a. Interrupted AC power supply. 1a. Check transformer connection and power

line circuit breaker.

2. Digital communicator mes-

sage not being received.

2a. Control in TEST mode.

2b. Telephone connection not secure.

2c. Digital communicator malfunctioning

2d. Telephone number in program needs prefix

or access code.

2e. Telephone call to central monitoring station

requires operator assistance.

2a. Remove from TEST mode.

2b. Check all connections.

2c. Check with a different VISTA–10SE.

2d. Program prefix or access code into the

control

2e. System cannot work in this situation.

3. Does not arm properly. 3a. READY light not on. 3a. Check for faulted zone(s) by pressing [✱] ;

make faulted zone(s) intact, or use

Bypass arming, if desired.

4. VISTA–10SE doesn't respond

to keystrokes on keypad.

4a. "CC" or "MODEM COMM" displayed.

4b. "d1" or "System Busy" displayed.

4c. "E4" or "E8" displayed.

4d. Keypad address setting incorrect.

4a. System is in communication with down-

loader at central station. Wait until down-

load session is finished.

4b. System has just been powered and is in

its one minute initialization. To bypass

this time, press '#' + '0'.

4c. More zones have been programmed than

the zone expansion modules can handle.

Delete some zones or use a higher

capability RF receiver.

4d. Keypads must be set for address 31 (non-

addressable mode).

SMOKE DETECTOR

SYMPTOM POSSIBLE CAUSE REMEDY

1. Detector alarms, no apparent

reason.

1a. Dust, dirt in sensing chamber.

1b. Improper location.

1c. Unit malfunctioning.

1a. Clean unit's sensing chamber with vacuum

cleaner per unit's instructions.

1b. See unit's instructions for locations to

avoid. Relocate as necessary.

1c. Replace detector.

2. Detector's siren sounds. 2a. Unit not receiving required power.

2b. Unit malfunctioning.

2a. Check for proper installation of battery. Try

new battery.

2b. Replace detector.

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Vistaquest N7227V5 Manuel d'utilisateur Page 78

Commentaires sur ces manuels